ABB ACS150 USER MANUAL PDF
ABB ACS Operation Limits. Setup the For settings of other parameters/ macros and detailed explanation hereof, see the instructions manual from ABB. View and Download ABB ACS user manual online. ACS Controller pdf manual download. The ABB ACS series component drives are easy to select and come with a variety of standard features acsuser-manual-partpdf.
|Genre:||Health and Food|
|Published (Last):||21 April 2004|
|PDF File Size:||19.23 Mb|
|ePub File Size:||5.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
ABB ACS150 – 0.75KW – IP20 – ACS150-01E-04A7-2
Overcurrent trip limit for drive is Check motor and motor abb including phasing. Page 44 Overview The following table summarizes the key functions and displays on the Integrated Control Panel. How to reset The drive can be reset either by pressing the keypad key on the control panel, through digital input, or by switching the supply voltage off for a while.
The chapter describes the construction and type code information in short. Comments to this Mnaual Your Name. Parameter modes There are two parameter modes: Ce Marking Applicable standards The drive complies with the following standards: Got it, continue to print. It also instructs in using the panel in control, monitoring and changing the settings. Control Panel The chapter describes the control panel keys and display fields. Safety What this chapter contains The chapter contains the safety instructions which you must follow when installing, operating and servicing the drive.
Page Below is a simple wiring diagram example. Selecting The Power Cables Selecting the power cables General rules Suer the input power and motor cables according to local regulations. Page 54 Control panel Reference mode In the Reference mode, you can: Output mode In the Output mode, you can: Hardware Description The chapter describes the construction and type code information in short.
Manua, 45 The ACS includes an maanual potentiometer located at the front of the drive. Planning Electrical Installation Note: Stop the drive and disconnect it from the AC power source. Wait until task is completed.
Installation Checklist Installation checklist Checklist Check the mechanical and electrical installation of the drive before start-up. For ACSx drives, other measures for protection in case of direct or indirect contact, such as separation from the environment by uxer or reinforced insulation or isolation from the supply system by a transformer, can also be applied.
Step Action Display Use keys to select the parameter value.
ABB ACS USER MANUAL Pdf Download.
Routing the cables Route the motor cable away from other cable routes. Motor Potentiometer macro This macro provides a cost-effective interface for PLCs that vary the speed used the drive using only digital signals.
Page 36 Installation checklist The table below contains a summary of the macros and describes suitable applications. The work described in this chapter may only be carried out by a qualified electrician.
To prevent dependent overheating, set IR compensation voltage as low as possible. Replacement fans are available from ABB. Page 16 Hardware description If not, contact an ABB representative. Mounting The Drive Free space around the drive The required free space for cooling above and below the drive is 75 mm 3 in. Make sure that dust from drilling does not enter the drive during the If Run Enable signal is switched on, the drive will not start or coasts to stop if it is running.
Available for two seconds at start, otherwise as long as 2max allowed by the drive temperature.
Industrial Component Drives ACS | Variable Speed AC Motor Drive (ABB) | ECD Controls
Page Symbols Input continuous rms input current Output continuous rms current. For the parameter default values, see section Default values with different macros on page Fasten clamping plates 1.
Task Mode Page How to switch between local and remote control How to start and stop the drive How to manuxl the direction of the motor rotation How to set the frequency reference Stop drive and change parameter value. Fuses must be used with other circuit breakers. The function is useful in applications where a smooth and quick restarting is essential. Fan failure can be predicted by the increasing noise from the fan usfr.
Symbols Input continuous rms input current Output continuous rms current.
Use a separate grounding cable abh the conductivity of the cable shield is insufficient smaller than the conductivity of the phase conductor and there is no symmetrically constructed grounding conductor in the cable see section Selecting the Ignoring the safety instructions can cause injury or death.